30 Comments

  1. ThE sToRy Of My LiFe
    January 27, 2019 @ 1:12 am

    I haven't seen any of Tom's episode that I didn't like.

    Reply

  2. Ravi Z
    January 29, 2019 @ 6:35 am

    Wow this the cleanest work I have seen

    Reply

  3. Vishwan Purandat
    February 2, 2019 @ 11:40 pm

    Wish Tommy was my grand dad

    Reply

  4. Bret .Maverick
    February 5, 2019 @ 3:43 am

    That guy lives on a busy road.

    Reply

  5. Corcoran Sullivan
    February 5, 2019 @ 6:46 am

    carpenter g.o.a.t.?

    Reply

  6. JoeyWalsh
    February 7, 2019 @ 3:06 am

    They literally just lifted this mans porch

    Reply

  7. Danny Ash
    February 8, 2019 @ 6:44 pm

    It's very tough to make those precision cuts with a Sawzall. He doesn't even break a sweat.

    Reply

  8. Snow G
    February 11, 2019 @ 8:02 am

    Which brand hydraulic jack do you recommend?

    Reply

  9. M J
    February 16, 2019 @ 10:20 pm

    i have no porch
    i have no post
    but don't know why i am watching this video
    but honestly after watching it i fill relaxing!

    Reply

  10. Tramopolis City
    February 17, 2019 @ 9:41 pm

    I love that there isn’t high production to these videos, just good information and hard work

    Reply

  11. Eliusalmo1
    February 23, 2019 @ 2:40 am

    Greatest!

    Reply

  12. Thunder Fang
    March 9, 2019 @ 8:10 pm

    I really don't mean to sound funny but I love you guys. You guys have taught me so much since I was a teenager God bless you for sharing your gifts.

    Reply

  13. thehal2000
    March 24, 2019 @ 2:55 am

    Tom is the man. Getting those nice scarf joints with a skilsaw and a reciprocating saw is pretty slick.

    Reply

  14. BrokeBandz
    March 26, 2019 @ 10:19 pm

    2:36 I thought he was going to say "You're ole post were a piece of ****".

    Reply

  15. Generatorblue Generator blues
    March 30, 2019 @ 5:25 am

    Can you imagine a machine that can duplicate a porch post while it is still installed in the vertical position. I can build such a machine with a little support from "This Old House." However, they are not been receptive to my ideas. I have a video entitled "chainsaw lathe" that shows the basic principle horizontally. But the new machine will cut from the top of the circular section of the post by following the contour of the post as it moves down. The cutting machine will slide down the replacement (slowly rotating square) new post centimeter by centimeter. the contour arm will control how deep the cut can be at each level. Once the amount of time it takes for the deepest cut is estimated, the machine can simply be allowed to cut for the same amount of time at every round level (at every centimeter). But the contour control arm will not allow the cutting machine to cut any deeper than is needed at every level. At the levels where the diameter of the post is larger, the cutting machine will be rotating for a fraction of the allowed time without being able to cut deeper. That waste of time will make noise but will simplify programming the control. I am in the Boston Area. You can also check my lathe design entitled: Haitian Lathe any size (one day project) by "PRPaul1 Inventions"

    Reply

  16. sticknstonesbrkbones
    March 31, 2019 @ 11:26 pm

    I like that. Im sure I will be using it someday. Thx for the post. lol that wasn't meant to be a pun

    Reply

  17. Harry S
    April 1, 2019 @ 6:47 pm

    How about a series strictly about house demolition called " Axe This Old House ?"

    Reply

  18. dave grier
    April 2, 2019 @ 10:33 pm

    Clowns of youtube take note. A master performs surgery with a sawzall and can clean it up with 60 seconds of sanding. Please don't post your trials.

    Reply

  19. Vlad Ada
    April 4, 2019 @ 4:44 am

    Bald guy so cringe

    Reply

  20. desimanable
    April 5, 2019 @ 10:31 pm

    these are so satisfying to watch.. =D

    Reply

  21. smiler
    April 5, 2019 @ 10:53 pm

    It wasn't lined up at the top. Which irked my OCD. But nice work.

    Reply

  22. Hammad
    April 9, 2019 @ 8:41 pm

    0:12 Porch post seduction

    Reply

  23. Ed Krippendorf
    April 12, 2019 @ 10:46 pm

    I love your videos

    Reply

  24. daniel melo
    April 19, 2019 @ 3:45 am

    very good.

    Reply

  25. pgreenx
    April 22, 2019 @ 12:32 am

    I wonder if every "craftsman" know how to do this but doesn't want to take the time

    Reply

  26. Corey Cooper Stevens
    May 6, 2019 @ 11:42 pm

    Not messing around. Way to go, Tommy. #Mastery

    Reply

  27. Jose Hernandez
    May 13, 2019 @ 12:02 am

    Wow amazing

    Reply

  28. Paul Trigger
    May 15, 2019 @ 5:30 am

    precision cuts with a reciprocating saw like a boss

    Reply

  29. DOCTORJAN714
    May 17, 2019 @ 4:39 pm

    They forgot to show the end when they found out that the posts were too far apart for the section of railing that they didn't replace yet.

    Reply

  30. Pyroman /
    May 19, 2019 @ 3:52 pm

    Funny how a 6×6 changed eh just like 2×4 and any other sized wood

    Reply

Leave a Reply

Your email address will not be published. Required fields are marked *